Fabrication guide Solvent bonding

By David Deng · R&D manager, Sanait · Updated November 2026

Yes. Extruded acrylic can be solvent-bonded. The joint is real. It is also less forgiving than a cast-to-cast joint, and it is the wrong default when the seam has to disappear on a show face. Specify the route on both sides of the joint. Do not assume “acrylic” means the bond will look like the sample.

The short answer

Decision rule. If the joint can be hidden, or a visible line is acceptable, extruded acrylic may be solvent-bonded. If the seam should disappear on a face the customer sees, specify cell-cast on both sides of that joint. “Can” is not the same as “will match a cast sample.”

What solvent bonding is

Solvent cement softens the PMMA at the mating faces so they fuse as the solvent leaves. It is not a gap-filling adhesive in the way a silicone or an epoxy is. Faces have to meet. A step from thickness variation, a wavy edge, or dirt in the joint becomes a line you can see.

The cement, the open time, the pressure, and the cure all change the result. Naming “solvent bond” without the route still leaves the factory free to use extruded on one side. That is how two quotes for a “clear box” describe different joints.

Why the route changes the joint

Cell-cast sheet — ISO 7823-1 — is the sheet display shops bond when the joint should read as one piece. Extruded sheet — ISO 7823-2 — is the same polymer made a different way. It can be cemented. In practice the joint is more sensitive: more blush, more tendency for the line to stay visible, less forgiveness if the faces are not flat.

That is a fabrication observation, not a strength ranking. A percentage of parent-sheet strength belongs to a named cement, a named cure, and a named test. Without those, leave the number off the page.

Which pairing for which joint

Joint pairing — what to specify, not a strength table
Pairing Usual role What to expect
Cast to cast Show corner on a cube or lid The normal disappearing joint, if faces meet and cement is right
Extruded to extruded Hidden corner, internal fixture, cost box A real joint; more often a visible line or blush
Cast to extruded Show face to a hidden back, if you accept the mix Possible; the seam will not behave like cast-to-cast
Either, with a gap Not a solvent-bond job Solvent cement does not fill a gap. Redesign the fit or change the joining method

Thickness tolerance feeds this. Cast’s wider band means two “5 mm” walls may not meet flush. A joint designed to the nominal, on either route, is how blush and steps get into the sample.

What a bad joint looks like

  • Blush. A white or cloudy halo along the seam. Often too much cement, too much working, or a stressed face.
  • Bubbles in the line. Air or uneven cement. The joint may still hold and still be a reject on a show face.
  • A hard visible line. Faces did not meet, or the extruded edge did not take the cement the way the sample implied.
  • Crazing nearby. Solvent plus residual stress. A different defect from a weak bond, and a reason not to flood the joint.

On a hidden corner these can be acceptable if the drawing says so. On a cosmetic cube they are usually scrap. Write which standard applies before the first article.

What to write on the RFQ

  1. PMMA route on each member that is bonded: cast, extruded, or a stated mix.
  2. Which joints must disappear, and which may show a line.
  3. That solvent bonding is the method — not “glued,” which a factory can read as something else.
  4. A fit note: faces meet, no designed gap.

Joints this decision sits on are the usual retail cases: boxes, related trays, and stands with a bonded foot.

Sanait will treat “clear joint” as a cast-to-cast request unless you say otherwise. How a brief is taken is on the FAQ. Scope is on the about page.

FAQ

Can you solvent-bond extruded acrylic?

Yes. The joint can be made. It is less forgiving than cast-to-cast, and it is not the default for a seam that should disappear.

Is an extruded joint as strong as a cast joint?

Do not answer that with a percentage. Strength depends on cement, route, cure, and the test. For a show face, specify cast because of how the joint looks, not because of an unpublished strength ratio.

Can I bond extruded to cast?

Yes, if you accept that the seam will not match a cast-to-cast sample. Write the mix on the drawing.

Why did the joint turn white?

Blush. Common causes are too much cement, working the joint too long, or solvent on a stressed face. It is a process defect, not proof that extruded cannot be bonded.

Is solvent cement the same as glue?

No. It softens PMMA so the faces fuse. It does not fill a gap. A drawing that says “glued” is ambiguous.

What should the quote restate?

Route on each bonded member, and which joints must be clear. A price that only says “acrylic box, bonded” has not answered this page.

About the author

David Deng

R&D manager at Sanait. 10+ years in acrylic fabrication; 2,000+ custom acrylic projects shipped across 20+ countries.

Sanait Co., Ltd. builds custom acrylic displays in Dongguan. This note is general fabrication practice. It does not state a joint strength. Plant terms are on the FAQ. Background is on the about page.

Sources

The two sheet routes are defined by the standards below. They do not define a solvent-joint strength.

  1. ISO 7823-1:2003, Plastics — Poly(methyl methacrylate) sheets — Part 1: Cast sheets. iso.org
  2. ISO 7823-2:2003, Plastics — Poly(methyl methacrylate) sheets — Part 2: Extruded sheets. iso.org
  3. “Poly(methyl methacrylate).” Wikipedia. en.wikipedia.org